Skip to content
ACT · Science

Measurement

Measurement appears in 3 reviewed ACT questions and sits in Science. Below are worked examples showing exactly how the exam tests it, with the answer marked and every distractor explained.

How Measurement is tested

Example 1Medium
Experiment 5: A student tested the accuracy of a thermometer by placing it in water baths prepared at known temperatures and recording the thermometer reading. Actual Temperature (°C) | Thermometer Reading (°C) | Error (°C) 0 | 1.2 | +1.2 20 | 21.0 | +1.0 40 | 40.6 | +0.6 60 | 60.2 | +0.2 80 | 80.0 | 0.0 100 | 99.9 | -0.1 Based on the data, which statement best describes the thermometer's accuracy?
  1. AThe thermometer is perfectly accurate at every temperature tested.
  2. BThe thermometer reads accurately at low temperatures but becomes inaccurate above 80°C.
  3. CThe thermometer overestimates temperature at low temperatures and becomes accurate near 80°C.Correct
  4. DThe thermometer consistently reads higher than the actual temperature at all of the tested values.

Why C is right

At low temperatures (0°C), the thermometer reads 1.2°C too high. The error decreases steadily with increasing temperature, reaching 0.0 at 80°C and -0.1 at 100°C. The thermometer overestimates at low temperatures and becomes increasingly accurate as temperature rises.
Why the other 3 choices miss
A
Incorrect because errors range from +1.2°C at 0°C to -0.1°C at 100°C, demonstrating the thermometer is not perfectly accurate across the range.
B
Incorrect because the thermometer is actually most accurate near 80–100°C; it is inaccurate at LOW temperatures, not above 80°C.
D
Incorrect because at 100°C the thermometer reads -0.1°C below actual — slightly underestimating — so it does not consistently read higher at all tested values.
Example 2Medium
Table 1 shows the results of a study comparing three methods of measuring the speed of light in a glass prism: Method | Measured Speed (×10⁸ m/s) | Standard Deviation | Number of Trials Time-of-flight | 1.973 | 0.024 | 20 Snell's Law refraction | 1.989 | 0.008 | 50 Foucault rotating mirror | 1.981 | 0.015 | 30 Accepted speed of light in glass: 1.988 × 10⁸ m/s. Which method shows the best combination of accuracy (closeness to accepted value) and precision (small standard deviation)?
  1. ATime-of-flight, because it has the largest deviation from accepted value.
  2. BSnell's Law refraction, because it has the smallest standard deviation and is closest to the accepted value.Correct
  3. CTime-of-flight, because it has the fewest trials.
  4. DFoucault rotating mirror, because its value and standard deviation both fall midway between those of the other two methods.

Why B is right

Snell's Law refraction has the smallest standard deviation (0.008 × 10⁸ m/s = high precision) and measured value of 1.989 × 10⁸ m/s compared to accepted 1.988 × 10⁸ m/s (difference = 0.001 × 10⁸ m/s = high accuracy). It is both the most precise and most accurate method.
Why the other 3 choices miss
A
Incorrect because time-of-flight has the largest deviation from the accepted value (1.973 vs. 1.988 × 10⁸ m/s = 0.015 × 10⁸ m/s difference), making it the least accurate, not the best.
C
Incorrect because fewer trials generally reduces statistical reliability, and time-of-flight has both the largest deviation from accepted value and the largest standard deviation.
D
Incorrect because being in the middle is not the best combination: Foucault's value (1.981) is farther from 1.988 than Snell's (1.989), and its standard deviation (0.015) is larger than Snell's (0.008), so Snell's Law refraction beats it on both accuracy and precision.
Example 3Easier
A student measured the density of five liquids at room temperature (20°C) using a graduated cylinder and balance. Mass (g) and volume (mL) for each: Water: 50.0 g, 50.0 mL. Ethanol: 39.4 g, 50.0 mL. Glycerol: 63.0 g, 50.0 mL. Olive oil: 46.0 g, 50.0 mL. Mercury: 678 g, 50.0 mL. If all five liquids were combined in a single container, from bottom to top, what would be the expected layering order (densest to least dense)?
  1. AMercury, water, glycerol, olive oil, ethanol
  2. BEthanol, olive oil, water, glycerol, mercury
  3. CMercury, glycerol, water, olive oil, ethanolCorrect
  4. DMercury, glycerol, olive oil, water, ethanol

Why C is right

Densities (g/mL): Mercury = 678/50 = 13.56. Glycerol = 63.0/50 = 1.26. Water = 50.0/50 = 1.00. Olive oil = 46.0/50 = 0.92. Ethanol = 39.4/50 = 0.788. Order from densest (bottom) to least dense (top): Mercury (13.56) → Glycerol (1.26) → Water (1.00) → Olive oil (0.92) → Ethanol (0.788).
Why the other 3 choices miss
A
Incorrect because water (1.00 g/mL) is less dense than glycerol (1.26 g/mL), so water floats above glycerol, not below it.
B
Incorrect because this is the reverse order (least dense to most dense); the densest liquid (mercury) should be at the bottom.
D
Incorrect because olive oil (0.92 g/mL) is less dense than water (1.00 g/mL), so olive oil floats above water; water does not float above olive oil.

Studied alongside

Other concepts from Science.