Skip to content
ACT · Science

Reaction rate

Reaction rate appears in 3 reviewed ACT questions and sits in Science. Below are worked examples showing exactly how the exam tests it, with the answer marked and every distractor explained.

How Reaction rate is tested

Example 1Easier
Experiment 4: A student investigated the effect of surface area on the rate of a decomposition reaction using hydrogen peroxide (H₂O₂) and manganese dioxide (MnO₂) as a catalyst. The student used the same total mass (2 g) of MnO₂ but in different forms. Form of MnO₂ | Surface Area (cm²) | Time to Produce 100 mL O₂ (sec) Single large chunk | 12 | 142 Several medium pieces | 48 | 58 Fine powder | 320 | 12 What conclusion about surface area and reaction rate is best supported by the data?
  1. AFine powder is a better catalyst than MnO₂ chunks because it is a different substance.
  2. BGreater catalyst surface area provides more reactive sites, increasing reaction rate.Correct
  3. CIncreasing surface area decreases reaction rate.
  4. DReaction rate is independent of catalyst surface area.

Why B is right

As surface area increases from 12 to 320 cm², the time to produce 100 mL O₂ decreases dramatically from 142 to 12 seconds. More surface area means more catalyst surface available for H₂O₂ molecules to interact with, increasing the frequency of productive collisions and thus reaction rate.
Why the other 3 choices miss
A
Incorrect because all three forms are MnO₂ — the same substance — so it is the surface area, not a different material, causing the difference.
C
Incorrect because the data show the opposite: greater surface area leads to faster reaction (less time), not a slower one.
D
Incorrect because the dramatic reduction in reaction time with increasing surface area clearly demonstrates that surface area affects reaction rate.
Example 2Medium
A chemist studied how temperature affects the rate of decomposition of hydrogen peroxide (H2O2 → H2O + ½O2) both with and without a manganese dioxide catalyst. Rate was measured as mL O2 produced per minute. Temperature (°C) | Rate without catalyst (mL/min) | Rate with catalyst (mL/min) 10 | 0.2 | 8.1 20 | 0.4 | 14.3 30 | 0.8 | 23.7 40 | 1.4 | 36.2 50 | 2.5 | 51.8 At 30°C, approximately how many times faster does the reaction proceed with the catalyst compared to without?
  1. A30 times fasterCorrect
  2. B3 times faster
  3. C10 times faster
  4. D50 times faster

Why A is right

At 30°C: rate without catalyst = 0.8 mL/min; rate with catalyst = 23.7 mL/min. Ratio = 23.7 / 0.8 = 29.6 ≈ 30 times faster. The data and relationship in the passage point to this result more directly than the other choices.
Why the other 3 choices miss
B
Incorrect because 3 times faster would mean the catalyzed rate is 0.8 × 3 = 2.4 mL/min, far below the observed 23.7 mL/min.
C
Incorrect because 10 times faster would be 0.8 × 10 = 8.0 mL/min, still much lower than 23.7 mL/min.
D
Incorrect because 50 times faster would be 0.8 × 50 = 40.0 mL/min, higher than the observed 23.7 mL/min at 30°C.
Example 3Medium
Experiment 5: A chemist studied the decomposition of nitrogen dioxide (2NO2 → 2NO + O2) at 300°C, measuring NO2 concentration over time: Time (s) | [NO2] (mol/L) 0 | 0.100 50 | 0.0787 100 | 0.0649 150 | 0.0552 200 | 0.0481 300 | 0.0380 400 | 0.0314 A student calculates the average reaction rate between t=0 and t=100 s. What is the correct value?
  1. A2.11 × 10⁻³ mol/L/s
  2. B3.51 × 10⁻⁴ mol/L/sCorrect
  3. C1.00 × 10⁻³ mol/L/s
  4. D6.49 × 10⁻⁴ mol/L/s

Why B is right

Average rate = Δ[NO2] / Δt = (0.100 - 0.0649) / 100 s = 0.0351 / 100 = 3.51 × 10⁻⁴ mol/L/s. The negative sign indicates consumption, but rate magnitude = 3.51 × 10⁻⁴ mol/L/s. The data and relationship in the passage point to this result more directly than the other choices.
Why the other 3 choices miss
A
Incorrect because 2.11 × 10⁻³ mol/L/s would result from dividing by 50 s instead of 100 s (using only the first half-interval).
C
Incorrect because 1.00 × 10⁻³ mol/L/s would result from dividing the initial concentration (0.100) by 100 s — incorrect use of initial value rather than change.
D
Incorrect because 6.49 × 10⁻⁴ mol/L/s would result from dividing the final concentration (0.0649 mol/L) by the time interval (100 s) rather than dividing the change in concentration.

Studied alongside

Other concepts from Science.