Table 3 shows the results of testing four different insulation materials in a standardized thermal resistance experiment. Each material (same thickness: 10 cm) was placed between a heat source at 80°C and a cold surface at 20°C:
Material | Thermal Conductivity (W/m·K) | Temperature at cold surface after 1 hr (°C)
Fiberglass | 0.040 | 21.8
Cellulose | 0.038 | 21.7
Spray foam | 0.026 | 20.8
Aerogel | 0.015 | 20.4
Note: Lower thermal conductivity = better insulator.
A homeowner wants the most effective insulation. Based on the data, which material should be chosen?
- AFiberglass
- BSpray foam
- CAerogelCorrect
- DCellulose
Why C is right
Aerogel has the lowest thermal conductivity (0.015 W/m·K), meaning it transmits the least heat. This is confirmed by the lowest cold-surface temperature after 1 hour (20.4°C, closest to the starting 20°C), indicating minimal heat transfer through the aerogel insulation.
Why the other 3 choices miss
- A
- Incorrect because fiberglass has the highest thermal conductivity (0.040 W/m·K) of the four materials, making it the least effective insulator in this comparison.
- B
- Incorrect because spray foam (0.026 W/m·K) is better than fiberglass and cellulose but still less effective than aerogel (0.015 W/m·K).
- D
- Incorrect because cellulose has the second-highest conductivity (0.038 W/m·K) and cold-surface temperature (21.7°C), indicating it is the second-least effective insulator.
A student measured the specific heat capacity of three unknown metals by heating each to 100°C and then dropping it into 200 mL of water at 20°C. The student recorded the final water temperature.
Metal | Mass (g) | Initial Temp (°C) | Final Water Temp (°C) | Specific Heat (J/g°C)
Metal A | 50 | 100 | 22.6 | 0.45
Metal B | 50 | 100 | 24.1 | 0.90
Metal C | 50 | 100 | 25.8 | 1.38
Based on the data, which metal transferred the most heat energy to the water?
- AMetal CCorrect
- BAll metals transferred equal heat energy.
- CMetal A
- DMetal B
Why A is right
The heat absorbed by the water equals m_water x c_water x (T_final - T_initial), so the metal that raised the water temperature the most transferred the most heat to it. Metal C produced the highest final water temperature (25.8°C, a 5.8°C rise) versus Metal B (24.1°C, 4.1°C) and Metal A (22.6°C, 2.6°C). Therefore Metal C transferred the most heat energy to the water, making choice A correct.
Why the other 3 choices miss
- B
- Incorrect because the different final water temperatures (22.6, 24.1, 25.8°C) clearly demonstrate that the metals transferred different amounts of heat.
- C
- Incorrect because Metal A produced the smallest water temperature increase (only 2.6°C), indicating it transferred the least heat.
- D
- Incorrect because Metal B produced an intermediate water temperature increase (4.1°C), less than Metal C's 5.8°C increase.
Experiment 4: A student measured the cooling rate of three liquids (water, oil, and salt water) after heating all three to 80°C and recording temperature every 5 minutes in a room at 22°C.
Time (min) | Water (°C) | Oil (°C) | Salt water (°C)
0 | 80 | 80 | 80
5 | 72 | 64 | 71
10 | 65 | 52 | 63
15 | 59 | 42 | 57
20 | 54 | 35 | 52
30 | 46 | 28 | 44
60 | 34 | 24 | 32
Which liquid cools most rapidly?
- ASalt water
- BAll three cool at identical rates.
- CWater
- DOilCorrect
Why D is right
After 30 minutes, oil has cooled to 28°C (only 6°C above room temperature), while water is at 46°C and salt water at 44°C. Oil reaches near-room temperature fastest because it has a lower specific heat capacity than water or salt water, requiring less energy to be lost per degree of temperature drop.
Why the other 3 choices miss
- A
- Incorrect because salt water (32°C at 60 min) cools only slightly faster than pure water (34°C at 60 min) and much slower than oil (24°C at 60 min).
- B
- Incorrect because the data clearly show oil cooling much faster than either water or salt water at every time point.
- C
- Incorrect because water remains at 34°C after 60 minutes, well above room temperature, while oil reached near-room temperature (24°C) by 60 minutes.