A chemist studied the titration of acetic acid (a weak acid) with sodium hydroxide (a strong base). The chemist recorded pH as base was added:
Volume NaOH Added (mL) | pH
0 | 2.87
5 | 4.14
10 | 4.74
15 | 5.35
20 | 7.00
22 | 8.20
25 | 11.50
At what volume of NaOH is the equivalence point reached, where the number of moles of acid equals the moles of base?
- A15 mL
- B25 mL
- C10 mL
- D20 mLCorrect
Why D is right
The equivalence point in an acid-base titration is marked by a sharp pH increase near neutral or slightly basic pH. In the data, the steepest jump occurs between 20 and 22 mL (pH 7.00 to 8.20), indicating the equivalence point is reached at approximately 20 mL of NaOH.
Why the other 3 choices miss
- A
- Incorrect because at 15 mL the pH is 5.35, which is still in the buffering region below neutral, not at equivalence.
- B
- Incorrect because at 25 mL the pH has already risen to 11.50, well past the equivalence point; the reaction reached equivalence at approximately 20 mL.
- C
- Incorrect because at 10 mL the pH is 4.74 — this is the half-equivalence point (where pH = pKa), not the equivalence point.
A chemist performed an experiment to determine the concentration of an unknown NaOH solution by titrating it with 0.150 M HCl. In three trials, the volumes of HCl required to reach the phenolphthalein endpoint were: Trial 1: 22.45 mL. Trial 2: 22.38 mL. Trial 3: 22.51 mL. The initial volume of NaOH used in each trial was exactly 25.00 mL. What is the concentration of the NaOH solution?
- A0.150 M
- B0.168 M
- C0.134 MCorrect
- D0.112 M
Why C is right
Average HCl volume = (22.45 + 22.38 + 22.51)/3 = 67.34/3 = 22.45 mL = 0.02245 L. Moles HCl = 0.150 M × 0.02245 L = 0.003368 mol. At the equivalence point: moles NaOH = moles HCl = 0.003368 mol. Concentration NaOH = 0.003368 mol / 0.02500 L = 0.1347 M ≈ 0.134 M.
Why the other 3 choices miss
- A
- Incorrect because 0.150 M would mean equal molarity to the HCl, but only 25.00 mL NaOH would need exactly 25.00 mL of 0.150 M HCl, not 22.45 mL.
- B
- Incorrect because 0.168 M would require fewer mL of a weaker acid to neutralize — the volume used (22.45 mL) is less than 25 mL, correctly indicating NaOH molarity is lower than HCl molarity.
- D
- Incorrect because 0.112 M would require less HCl (~18.7 mL) to reach equivalence with 25.00 mL of NaOH.
A student performed an experiment to study the neutralization reaction between HCl and NaOH. Equal volumes (50 mL) of HCl were titrated with NaOH until the phenolphthalein endpoint was reached. The student varied HCl concentration and measured the volume of NaOH required. All NaOH solutions had a concentration of 0.5 M. Results: HCl concentration (M) / Volume NaOH (mL): 0.1 M HCl: 10.0 mL NaOH. 0.2 M: 20.0 mL. 0.3 M: 30.0 mL. 0.4 M: 40.0 mL. 0.5 M: 50.0 mL. If 50 mL of 0.35 M HCl were titrated with 0.5 M NaOH, what volume of NaOH would be needed?
- A35.0 mLCorrect
- B25.0 mL
- C17.5 mL
- D45.0 mL
Why A is right
From the data, a pattern is clear: moles HCl = moles NaOH at equivalence. Moles HCl = 0.35 M × 0.050 L = 0.0175 mol. Volume NaOH needed = moles / concentration = 0.0175 / 0.5 = 0.035 L = 35.0 mL. Alternatively, by interpolation: 0.3 M HCl requires 30 mL NaOH and 0.4 M requires 40 mL NaOH; 0.35 M (midpoint) requires 35 mL.
Why the other 3 choices miss
- B
- Incorrect because 25.0 mL corresponds to 0.5 M × 0.025 L = 0.0125 mol NaOH, equaling 0.25 M HCl × 0.05 L — not enough for 0.35 M HCl.
- C
- Incorrect because 17.5 mL would correspond to 0.5 M × 0.0175 L = 0.00875 mol NaOH, which would neutralize only half the moles of HCl present.
- D
- Incorrect because 45.0 mL corresponds to neutralizing 0.45 M HCl × 0.05 L = 0.0225 mol — more than needed for 0.35 M HCl.