In a data set with values 5, 8, 12, 15, 20, 24, 30, 35, 40, and 100, the value 100 is identified as a potential outlier. If 100 is removed from the data, which summary statistics change the most?
- AThe mean and standard deviation change the most.Correct
- BThe mean and IQR change the most.
- CThe median and standard deviation change the most.
- DThe median and IQR change the most.
Why A is right
The mean uses all values in its calculation and is pulled toward extreme values. Removing 100 would substantially decrease the mean. The standard deviation also uses all values and measures deviation from the mean; removing an extreme value decreases it significantly. The median and IQR are resistant measures and change little when an outlier is removed.
Why the other 3 choices miss
- B
- The IQR is a resistant measure based on quartiles. Removing one extreme value would have minimal effect on Q1 and Q3, thus little effect on IQR.
- C
- While the SD is non-resistant, the median is resistant to outliers. The median would shift very little after removing 100.
- D
- The median and IQR are resistant to outliers. Removing a single extreme value causes minimal change in these measures.
An analyst examines data on the number of defects per batch in a manufacturing process. The distribution is symmetric with mean 4.2 and standard deviation 1.8. Which interval contains approximately 99.7% of batch defect counts?
- A(−1.2, 9.6)Correct
- B(1.8, 6.6)
- C(2.4, 6.0)
- D(0.6, 7.8)
Why A is right
By the 68-95-99.7 (empirical) rule, approximately 99.7% of data in a roughly symmetric, bell-shaped distribution falls within ±3 standard deviations of the mean. Lower bound = 4.2 − 3(1.8) = 4.2 − 5.4 = −1.2. Upper bound = 4.2 + 3(1.8) = 4.2 + 5.4 = 9.6. So the interval is (−1.2, 9.6), which is choice A. (Choice D, (0.6, 7.8), is mean ± 2 SD ≈ 95%; choice C, (2.4, 6.0), is mean ± 1 SD ≈ 68%.)
Why the other 2 choices miss
- B
- (1.8, 6.6) = mean ± 1.33 SD approximately, which does not correspond to a standard interval.
- C
- (2.4, 6.0) = mean ± 1 SD, which contains approximately 68% of the data.
A large school district's records show that 30% of its students ride a bus to school. A researcher plans to take a random sample of students and compute p-hat, the proportion who ride a bus. If the sample size is increased from n = 100 to n = 400, how does the standard deviation of the sampling distribution of p-hat change?
- AIt decreases to one-fourth, about 0.011.
- BIt stays the same, at about 0.046.
- CIt decreases by half, from about 0.046 to about 0.023.Correct
- DIt doubles, to about 0.092.
Why C is right
The standard deviation of the sampling distribution of p-hat is sqrt(p(1-p)/n). With p = 0.30 and n = 100, it is sqrt(0.21/100) = sqrt(0.0021), about 0.0458. With n = 400, it is sqrt(0.21/400) = sqrt(0.000525), about 0.0229. Multiplying n by 4 divides the standard deviation by sqrt(4) = 2, so the spread is cut in half.
Why the other 3 choices miss
- A
- Divides the standard deviation by 4 instead of by sqrt(4) = 2. This forgets that n is under a square root (0.0458/4 is about 0.011).
- B
- Assumes the spread of p-hat depends only on p and not on sample size, so it ignores the n in the denominator of sqrt(p(1-p)/n).
- D
- Gets the direction wrong by thinking a larger sample gives more variability, perhaps mixing up the spread of a count with the spread of a proportion. A larger n makes p-hat less variable, not more.