Skip to content

Unit 5 of 7

Energy Resources and Consumption

12% of the exam86 reviewed questions24 key terms18 min read

Energy Resources and Consumption is worth about 12% of the AP Environmental Science exam. Our bank tests it with 86 reviewed questions across 24 distinct ideas — 25 easier, 52 medium and 9 harder.

On this page · 12 sections

Every power source you study in this unit does the same basic job. It takes energy stored in some form, such as carbon bonds in coal, an unstable uranium nucleus, water held behind a dam or photons from the Sun, and converts it into electricity or heat. The exam wants you to trace that chain of conversions and say what each step costs the environment. Coal, nuclear and biomass plants boil water into steam that spins a turbine. Steam-cycle plants such as coal and nuclear are only about 33 to 35 percent efficient, so they waste about two-thirds of their fuel energy as heat. Combined-cycle gas plants do better, at about 50 to 60 percent, but every thermal plant still loses a large share as heat and needs cooling.

The second thread is comparison. Fossil fuels still supply roughly 80 percent of the world's energy because they are dense, cheap and available on demand. Renewable sources such as solar, wind, hydroelectric and geothermal avoid most combustion pollution, but they depend on location and weather. To compare sources fairly, you need tools that look past the smokestack: energy return on investment (EROI), capacity factor and lifecycle analysis. A source that looks clean at the outlet can carry real costs in mining, manufacturing, land use or methane leaks.

The third thread is demand. The cheapest and cleanest unit of energy is the one you never use, so efficiency and conservation show up constantly. Expect questions on LED lighting, insulation, mass transit, net-zero buildings and the Jevons paradox, where efficiency gains can raise total use. The unit ends with the energy transition itself: how a grid built for steady fossil plants absorbs variable wind and solar, and why poorer countries find that switch harder.

The unit in a minute

One line per topic. Tap any line for the full notes.

  1. Energy units, conversions and the calculation questionsEnergy = power × time. Convert units step by step, keep units on every number, and divide by efficiency to find the input energy.
  2. Coal and natural gas: how burning fossil fuels makes powerCoal is the dirtiest fuel per unit of energy. Natural gas burns cleaner, but methane leaks reduce its climate advantage.
  3. Oil, tar sands and fracking: getting harder-to-reach fuelFracking uses high-pressure water, sand and chemicals to crack shale. Its main risks are water use, groundwater contamination, methane leaks and induced earthquakes.
  4. Nuclear power: fission, waste and accidentsNuclear power trades clean air and very low CO2 for long-lived radioactive waste and a small risk of catastrophic accidents.
  5. Biomass and the carbon-neutral debateCarbon-neutral means emissions are balanced by recent absorption, not that no CO2 is released. Carbon debt, fossil inputs and land clearing make many biomass sources less neutral than they appear.
  6. Solar, wind, hydroelectric and geothermalSolar, wind, hydro and geothermal avoid combustion, but each depends on location and carries its own land, wildlife or water trade-off.
  7. Comparing sources: EROI, capacity factor and lifecycle emissionsEROI measures energy profit, capacity factor measures reliability, and lifecycle analysis measures total impact. A source can rank well on one and badly on another.
  8. Efficiency, the grid, storage and the energy transitionEfficiency and storage make the transition possible, but the benefit of EVs, hydrogen fuel cells and net-zero buildings depends on the energy source behind them.
Grind Energy Resources and Consumption questionsAlready know this? Skip the notes and prove it.

The big ideas

Energy is converted, never created, and every conversion loses some as heat

Power plants do not make energy. They move it from one form to another, and each step loses some energy as low-quality heat, as the second law of thermodynamics requires. A coal plant runs chemical energy to thermal energy to mechanical energy to electrical energy, and only about 33 to 35 percent of the coal's energy reaches the wire. A hydroelectric dam skips combustion entirely: gravitational potential energy becomes kinetic energy, then electrical energy, which is why hydro is far more efficient. If you can name the chain of conversions for a source, you can usually predict its efficiency and its waste.

No source is free of impact; the impacts just land in different places

Coal and oil hurt the air through CO2, sulfur dioxide, nitrogen oxides, mercury and particulates. Nuclear power keeps the air clean but leaves spent fuel that stays dangerous for thousands of years. Dams block fish and flood valleys, solar panels need mined silicon and land, and wind turbines kill some birds and bats. The exam rewards answers that name the specific trade-off for a specific source instead of calling one source simply good or bad.

Fair comparisons count the whole life of a source

Emissions at the plant are only part of the story. Lifecycle analysis adds the mining, building, transport, operation and disposal stages. Seen that way, nuclear and wind have the lowest lifecycle emissions of any source, about 11 to 12 g CO2/kWh, lower even than solar PV at about 40 to 50. All three sit far below natural gas, which looks worse once methane leaks from wells and pipelines are counted. EROI asks how much energy you get back for the energy you spend, and capacity factor asks how much of the time a plant actually produces. Together these numbers explain why a source can be clean but unreliable, or reliable but dirty.

Using less energy is usually cheaper than making more

Efficiency means getting the same service from less energy, like light from an LED instead of an incandescent bulb. Conservation means choosing to use less, like turning off that light. Both cut emissions without building a single new plant. The catch is the rebound effect: when efficiency makes energy cheaper to use, people use more of it, so part of the savings disappears. The Jevons paradox is the extreme case, where efficiency gains lead to higher total energy consumption than before.

Study notes

8 topics. Each one opens with its key idea, then the detail you need to use it.

1. Energy units, conversions and the calculation questions

Key idea: Energy = power × time. Convert units step by step, keep units on every number, and divide by efficiency to find the input energy.

Most calculation questions in this unit chain a few unit conversions, so learn the units first. Power is the rate of energy use, measured in watts (W). Energy is power multiplied by time, so a 100-watt bulb running for 10 hours uses 1,000 watt-hours, or 1 kilowatt-hour (kWh). A megawatt (MW) is 1,000 kilowatts. A typical energy calculation might ask what you save by swapping a 60 W incandescent bulb for a 10 W LED that gives the same light. The saving is 50 W. Run for 5 hours a day for 365 days, that is 50 × 5 × 365 = 91,250 Wh, or about 91 kWh a year. At $0.15 per kWh, that saves about $13.70 per bulb. Efficiency problems work the same way. If a coal plant is 35 percent efficient and must deliver 350 MWh of electricity, it has to burn coal containing 350 ÷ 0.35 = 1,000 MWh of energy. The other 650 MWh leaves as waste heat. Always write each unit next to each number, because the units tell you whether to multiply or divide. The exam often gives one number per step and rewards you for showing the setup, not just the answer.

2. Coal and natural gas: how burning fossil fuels makes power

Key idea: Coal is the dirtiest fuel per unit of energy. Natural gas burns cleaner, but methane leaks reduce its climate advantage.

Fossil fuels are the remains of ancient organisms, buried and pressed over millions of years until their carbon became coal, oil or natural gas. They are nonrenewable because they form far more slowly than we use them. Coal power works by burning coal to boil water. The steam spins a turbine, and the turbine turns a generator. Coal comes in ranks: lignite, subbituminous, bituminous and anthracite. Higher ranks hold more carbon and release more energy per kilogram. Burning coal releases the most CO2 of any fossil fuel per unit of energy. It also releases sulfur dioxide, which causes acid rain, plus nitrogen oxides, mercury and particulates, and it leaves large piles of fly ash. Mining adds harm through strip mining, mountaintop removal and acid mine drainage. Natural gas is mostly methane (CH4). Burning it for electricity releases roughly half the CO2 of coal and almost no sulfur or mercury, which is why many utilities switched from coal to gas. The weak point is leakage. Methane traps about 28 times more heat than CO2 over 100 years, so leaks from wells and pipelines erase part of gas's advantage. Gas plants can also ramp up and down in minutes, so grids use them to fill gaps when demand spikes.

3. Oil, tar sands and fracking: getting harder-to-reach fuel

Key idea: Fracking uses high-pressure water, sand and chemicals to crack shale. Its main risks are water use, groundwater contamination, methane leaks and induced earthquakes.

Crude oil is refined into gasoline, diesel, jet fuel and plastics, and it dominates transportation. As easy oil fields decline, companies turn to harder sources, which costs more energy and causes more damage. Tar sands, like those in Alberta, Canada, hold a heavy oil called bitumen mixed with sand and clay. Getting it out takes strip mining or steam injection, both of which use large amounts of water and energy. Fracking, or hydraulic fracturing, unlocks oil and natural gas trapped in tight shale rock. Drillers bore down and then turn sideways through the shale. They pump water, sand and chemicals at high pressure to crack the rock, and the sand props the cracks open so gas can flow out. Fracking made the United States the world's top producer of natural gas. Its risks follow from that method. Each well uses millions of gallons of water. Chemicals and methane can contaminate groundwater if a well casing fails. Methane leaks at the surface add greenhouse gas. Injecting used wastewater deep underground has triggered thousands of earthquakes in Oklahoma since about 2009. Most were small, but some were damaging, such as the magnitude 5.7 quake near Prague in 2011 and the magnitude 5.8 quake near Pawnee in 2016. Fracked gas is still fossil fuel, so cheaper gas also slows the shift to renewables.

4. Nuclear power: fission, waste and accidents

Key idea: Nuclear power trades clean air and very low CO2 for long-lived radioactive waste and a small risk of catastrophic accidents.

Nuclear energy comes from fission, the splitting of heavy nuclei. In a reactor, a neutron strikes a uranium-235 nucleus, which splits into smaller nuclei and releases heat plus two or three more neutrons. Those neutrons split more U-235 atoms, so the reaction sustains itself as a chain reaction. Natural uranium is only about 0.7 percent U-235, so fuel is enriched to about 3 to 5 percent. Control rods made of boron or cadmium absorb neutrons and slow the reaction. The heat boils water into steam that drives a turbine, the same back end as a coal plant. During operation, nuclear power produces no CO2, sulfur dioxide or particulates. Its lifecycle emissions are about as low as wind's. The cost is spent fuel, which stays radioactive for thousands of years because isotopes such as plutonium-239 have a half-life of about 24,000 years. Half-life questions are simple halving: after 3 half-lives, 1/8 of the original isotope remains. The United States still has no permanent repository, so spent fuel sits in cooling pools and dry casks at power plants. Plants also release heated water that causes thermal pollution. The three famous accidents all involved overheating. Three Mile Island in Pennsylvania suffered a partial meltdown in 1979. A reactor at Chernobyl in Ukraine exploded in 1986. At Fukushima in Japan in 2011, an earthquake caused a tsunami that flooded the backup generators and stopped the cooling, so three cores melted down.

5. Biomass and the carbon-neutral debate

Key idea: Carbon-neutral means emissions are balanced by recent absorption, not that no CO2 is released. Carbon debt, fossil inputs and land clearing make many biomass sources less neutral than they appear.

Biomass energy comes from organic matter: wood, crop residues, animal dung, and biofuels such as corn ethanol and biodiesel. Plants store solar energy as chemical energy through photosynthesis, so biomass is renewable if it is regrown as fast as it is used. Biomass is called carbon-neutral because burning it releases CO2 that the plants recently pulled from the air. The definition matters. Carbon neutrality does not mean zero CO2 at the smokestack. It means no net increase in atmospheric CO2 once regrowth is counted. Critics argue that biomass is often not neutral in practice, for three reasons. First, harvesting, processing and trucking biomass burn fossil fuels. Second, there is a time lag called carbon debt. Burning a mature forest releases decades of stored carbon at once, while regrowth can take 20 to 100 years or more to absorb it again. During that period, the atmosphere holds more CO2 than if nothing had been burned. Third, clearing land for fuel crops releases soil and forest carbon. Corn ethanol also has a low EROI, close to 1:1 in some studies, because farming takes fertilizer, fuel and machinery. In developing countries, people often burn wood and dung indoors for cooking, which causes serious indoor air pollution and drives deforestation.

6. Solar, wind, hydroelectric and geothermal

Key idea: Solar, wind, hydro and geothermal avoid combustion, but each depends on location and carries its own land, wildlife or water trade-off.

These renewable sources skip combustion, so they produce almost no air pollution while running. Each one, though, depends on place. Solar energy reaches us in three forms. Passive solar design uses south-facing windows (in the Northern Hemisphere) and thick walls to soak up heat. Active solar uses pumps to move heated water or air. Photovoltaic (PV) cells use silicon semiconductors: incoming photons knock electrons loose, creating a direct current that an inverter converts for the grid. Solar output drops at night and under clouds, and panel making requires mining and some toxic chemicals. Wind turbines turn the kinetic energy of moving air into electricity. Power rises with the cube of wind speed, so doubling wind speed gives about 8 times the power. That is why turbines stand on ridges, plains and offshore. Downsides include bird and bat deaths and noise. Hydroelectric dams convert the gravitational potential energy of stored water into kinetic energy and then electrical energy. Dams flood valleys, displace people, block salmon migration, trap sediment and change downstream temperature. China's Three Gorges Dam displaced more than a million people. Geothermal plants tap steam or hot water heated by magma, so they work best near plate boundaries and hotspots, such as Iceland, California and the Philippines. Ground-source heat pumps are different: they use the steady temperature a few meters underground and work almost anywhere.

7. Comparing sources: EROI, capacity factor and lifecycle emissions

Key idea: EROI measures energy profit, capacity factor measures reliability, and lifecycle analysis measures total impact. A source can rank well on one and badly on another.

Energy comparison questions give you a table and ask which source wins on one measure, so know what each measure means. EROI, or energy return on investment, divides the energy a source delivers by the energy spent to get it. An EROI of 40:1 means 40 units out for every 1 unit in. Large hydroelectric dams top most lists at around 40:1 or more, because once the dam is built, gravity and the water cycle supply the fuel for 50 to 100 years. Oil fields in the 1930s returned close to 100:1, but harder-to-reach oil now returns far less, and corn ethanol barely breaks even. A low EROI means much of the energy is used up just producing the fuel. Capacity factor compares what a plant actually produces in a year with what it would produce running at full power nonstop. US nuclear plants run at about 90 percent. Wind usually runs at about 35 percent and solar PV at about 25 percent, because the wind dies down and the Sun sets. To find yearly output, multiply rated power × 8,760 hours × capacity factor. A 100 MW wind farm at 35 percent makes about 306,600 MWh a year. Lifecycle analysis tracks impacts from mining to disposal. Its lifecycle emissions figures, in grams of CO2 per kWh, run roughly 820 for coal, 490 for natural gas, about 40 to 50 for solar PV, and about 11 to 12 for both nuclear and wind.

8. Efficiency, the grid, storage and the energy transition

Key idea: Efficiency and storage make the transition possible, but the benefit of EVs, hydrogen fuel cells and net-zero buildings depends on the energy source behind them.

Energy efficiency gets the same service from less input. LEDs use about 75 to 80 percent less electricity than incandescent bulbs, which waste most of their energy as heat. Insulation, double-paned windows and heat pumps cut building energy use. Cogeneration captures a power plant's waste heat to warm nearby buildings. In transport, a full bus or train uses far less energy per passenger-mile than a car carrying one driver. CAFE standards raise the average fuel economy that carmakers must meet. A net-zero energy building still uses energy and usually stays connected to the grid. It produces as much renewable energy on site, often from rooftop solar, as it uses over a full year. The Jevons paradox warns that efficiency can lower the cost of using energy, which raises demand. Grid management is the job of matching supply to demand second by second. That is hard with solar and wind, which vary with weather. Energy storage smooths the gaps. Options include lithium-ion batteries, pumped hydro, which pumps water uphill when power is cheap and releases it later, and hydrogen made by splitting water. Hydrogen is an energy carrier, not an energy source, because making it takes more energy than it later returns. A fuel cell combines hydrogen (H2) with oxygen (O2) from the air to make electricity directly, and its only byproducts are water and some heat. Most hydrogen today is stripped from natural gas, which releases CO2. The cleaner route is electrolysis, which splits water using electricity, so the hydrogen is only as clean as the power used to make it. Electric vehicles have zero tailpipe emissions, and their motors turn about 85 to 90 percent of battery energy into motion. Their real benefit depends on how the grid makes its electricity. The energy transition is hardest in developing countries, which need cheap power to grow and often lack the money to build renewable grids without international help.

Common mistakes

Drawn from the wrong answers students actually pick on these questions.

Thinking a net-zero energy building uses no energy or is cut off from the grid.

A net-zero building uses energy all year and usually stays grid-connected. It draws power at night and feeds surplus solar back on sunny days. Over 12 months its on-site renewable output equals its use. Being off-grid is a separate idea, and a building that runs on fossil grid power without offsetting it is not net-zero.

Assuming energy efficiency always lowers total energy use.

That assumption is exactly what the Jevons paradox challenges. When efficiency makes energy cheaper to use, people often use more, such as driving farther in a fuel-efficient car. The paradox is about efficiency and consumption. It is not about whether renewables cost more or about population growth, even though population does raise demand on its own.

Mixing up the environmental profiles of nuclear and coal power.

Coal releases far more CO2 per kWh than nuclear, along with sulfur dioxide, nitrogen oxides, mercury and particulates. Nuclear releases almost no air pollution while running. Their waste problems differ too. Coal leaves huge volumes of ash and slag, while nuclear leaves a small volume of spent fuel that stays radioactive for thousands of years.

Defining carbon-neutral as producing no CO2, or as producing cheap energy.

A carbon-neutral source does release CO2 when it is used. It counts as neutral because that CO2 was recently absorbed, so there is no net rise in atmospheric carbon. The term describes the carbon balance in the air, not the cost of the electricity or whether carbon ends up as ash.

Giving a hydroelectric dam the same energy chain as a fossil fuel plant.

Chemical energy to steam to electricity describes a coal, gas or biomass plant. Solar to chemical to electrical describes biomass, where photosynthesis stores the energy and burning it later makes power. A fuel cell is different again: it turns chemical energy, such as hydrogen, directly into electrical energy. A dam burns nothing: gravitational potential energy of stored water becomes kinetic energy as it falls, which spins the turbine and generator to make electrical energy.

Claiming electric vehicles have tailpipe emissions or always use more energy per mile.

EVs have zero tailpipe emissions for their whole lives, and their motors convert about 85 to 90 percent of stored energy into motion, compared with 20 to 30 percent for gasoline engines. Their real limits are the grid's power source, battery mining, charging stations and driving range. On a coal-heavy grid, their lifecycle benefit shrinks.

How this unit shows up on the exam

Energy is about 12 percent of the AP Environmental Science exam, and it appears in both sections. Multiple-choice stems usually take one of four shapes. Some ask you to define a term, such as carbon-neutral, net-zero or Jevons paradox, with distractors that sound close but miss the key word, like a building that uses no energy at all or one cut off from the grid. Some ask for an energy conversion chain, such as the sequence inside a dam or a reactor. Some give a short scenario, like a town choosing a geothermal site or a critic attacking biomass, and ask which fact best supports a claim. Others give a data table of EROI, capacity factor or lifecycle emissions and ask you to compare. Read the column headings first, since a source can lead on one measure and trail on another.

Expect at least one free-response question that requires calculations, and energy is a favorite topic for it. Expect to convert watts to kilowatt-hours, find yearly cost savings, or work back from plant efficiency to fuel burned. Readers award points for a visible setup with units, so write every step. On the analyze-a-problem questions, you are asked to identify an impact and propose a solution. The answers that earn points are specific and causal. Saying that coal combustion releases sulfur dioxide, which forms acid rain and lowers lake pH, earns credit. Saying coal is bad for the environment does not. When asked for a disadvantage of a renewable source, name the mechanism, such as intermittency, habitat loss behind a dam, or location limits for geothermal.

How the exam actually asks it

Real items from the AP Environmental Science bank, easier first. The answer is marked, and every wrong choice is explained — because knowing why a distractor is tempting is most of the work.

Worked example 1Easier
A building achieves net-zero energy when it
  1. Agenerates as much renewable energy on-site as it consumes over the course of a yearCorrect
  2. Bis disconnected from all utility services, including the electric grid and natural gas lines
  3. Cconsumes no energy at any time throughout the year
  4. Duses only fossil fuel-generated electricity

Why A is right

A net-zero energy building produces as much renewable energy (typically through rooftop solar) as it consumes annually. It may draw from the grid at times but offsets that use by feeding surplus energy back at other times.
Why the other 3 choices miss
B
Incorrect because net-zero buildings are typically grid-connected to balance supply and demand; being off-grid (cut off from the electric grid and gas lines) is a different concept.
C
Incorrect because net-zero buildings do consume energy; the 'net' means their renewable generation balances their consumption over the year.
D
Incorrect because using fossil fuel electricity would not be net-zero; the building must generate equivalent renewable energy to offset its consumption.
Worked example 2Easier
Which of the following energy transformations occurs in a hydroelectric dam?
  1. AChemical energy in fuel → thermal energy in steam → electrical energy
  2. BGravitational potential energy → kinetic energy → electrical energyCorrect
  3. CSolar energy → chemical energy → electrical energy
  4. DNuclear energy in fuel → thermal energy in steam → electrical energy

Why B is right

In hydroelectric generation, water stored at height has gravitational potential energy. As it flows downhill through turbines, this converts to kinetic energy of moving water, which spins turbines connected to generators that produce electrical energy.
Why the other 3 choices miss
A
Incorrect because chemical energy in fuel to thermal energy in steam to electrical energy describes fossil fuel combustion in thermal power plants, not hydroelectric generation.
C
Incorrect because solar to chemical to electrical describes biomass energy or fuel cells, not the direct mechanical energy conversion in hydroelectric systems.
D
Incorrect because nuclear energy in fuel to thermal energy in steam to electrical energy describes nuclear power plants, where fission heats water to steam, not hydroelectric dams.
Worked example 3Easier
Which of the following represents the most energy-efficient mode of passenger transportation per passenger-mile?
  1. AA single-occupancy SUV
  2. BA short-haul domestic flight
  3. CA fully loaded commuter bus or passenger trainCorrect
  4. DA private helicopter

Why C is right

Fully loaded buses and trains are the most energy-efficient passenger transport modes per passenger-mile because they carry many passengers while consuming relatively little additional fuel per person. This gives them the lowest per-passenger energy consumption.
Why the other 3 choices miss
A
Incorrect because single-occupancy vehicles use all their fuel to move one person, making them among the least efficient per passenger-mile.
B
Incorrect because short-haul flights use disproportionate fuel during takeoff and landing relative to distance traveled, making them less efficient than rail or bus.
D
Incorrect because helicopters consume large amounts of fuel relative to the few passengers they carry, making them very energy-intensive per passenger-mile.
Worked example 4Easier
A community is evaluating whether to build a geothermal power plant. Which geological condition is most essential for a viable geothermal energy facility?
  1. AA region with consistently high wind speeds throughout the year
  2. BProximity to large rivers with steep elevation gradients
  3. CPresence of large coal deposits near the surface
  4. DLocation near tectonic plate boundaries where magma heats underground waterCorrect

Why D is right

Geothermal power plants require access to underground reservoirs of hot water or steam heated by magma or hot rock. These conditions are most commonly found near tectonic plate boundaries, volcanic hotspots, or areas with geothermal gradients high enough to heat water to useful temperatures. Locations like Iceland, parts of the western United States, and the Philippines sit on active plate boundaries and are ideal for geothermal energy production.
Why the other 3 choices miss
A
Incorrect because consistent high wind speeds are the essential condition for wind energy production, not geothermal energy.
B
Incorrect because large rivers with steep elevation gradients are the essential condition for hydroelectric power generation, not geothermal energy.
C
Incorrect because coal deposits are a fossil fuel resource unrelated to geothermal energy. Geothermal energy harnesses heat from Earth's interior, not from combustible mineral deposits.

Can you do all of these?

Tick what you can do without looking. Anything left unticked is where to go back to.

0 of 11 ticked

Ready to test yourself?

Open practice pulls from the 26 free questions in this unit. The other 60 come with the one-time AP purchase, which unlocks every AP course.

Official topic list

The official course framework breaks this unit into 13 numbered topics.

  1. 6.1Renewable and Nonrenewable Resources
  2. 6.2Global Energy Consumption
  3. 6.3Fuel Types and Uses
  4. 6.4Distribution of Natural Energy Resources
  5. 6.5Fossil Fuels
  6. 6.6Nuclear Power
  7. 6.7Energy from Biomass
  8. 6.8Solar Energy
  9. 6.9Hydroelectric Power
  10. 6.10Geothermal Energy
  11. 6.11Hydrogen Fuel Cell
  12. 6.12Wind Energy
  13. 6.13Energy Conservation

Key terms in Energy Resources and Consumption

Ordered by how often our reviewed questions test them. Open any term to see the questions that use it.

The rest of AP Environmental Science

Every unit with its share of the exam. You are on Unit 5.

  1. 1Living World: Ecosystems and Biodiversity15% of exam
  2. 2Populations13% of exam
  3. 3Earth Systems and Resources13% of exam
  4. 4Land and Water Use12% of exam
  5. 5Energy Resources and Consumption12% of exam
  6. 6Atmospheric, Aquatic, and Terrestrial Pollution17% of exam
  7. 7Global Change18% of exam