Skip to content

Unit 5 of 7

Torque and Rotational Dynamics; Energy and Momentum of Rotating Systems

19% of the exam341 reviewed questions30 key terms18 min read

Torque and Rotational Dynamics; Energy and Momentum of Rotating Systems is worth about 19% of the AP Physics 1 exam. Our bank tests it with 341 reviewed questions across 30 distinct ideas — 32 easier, 244 medium and 65 harder.

On this page · 12 sections

Everything you learned about forces and motion in the earlier units has a rotating twin. Force becomes torque, mass becomes moment of inertia, and momentum becomes angular momentum, so if you know F = ma you already know the shape of τ = Iα. The new work is learning what each rotational quantity depends on, because that is where the exam sets its traps.

Two quantities carry the first half of the unit. Torque measures how well a force twists an object about an axis, and it depends on where and in what direction you push, not just how hard. Moment of inertia measures how hard an object is to spin up, and it depends on where the mass sits relative to the axis, not just how much mass there is. Together, τnet = Iα predicts how any rigid object speeds up, slows down or stays balanced.

The second half carries energy and momentum into rotation. A spinning object stores kinetic energy ½Iω², and a rolling object stores translational and rotational energy at the same time. Angular momentum stays constant whenever no net external torque acts, which explains a spinning skater, a satellite in an elliptical orbit and a ball on a shrinking string. Most hard questions mix these tools, so decide which one fits before you calculate anything.

The unit in a minute

One line per topic. Tap any line for the full notes.

  1. Angular kinematics: describing rotationConvert revolutions to radians first, then use the Unit 1 equations with θ, ω and α in place of x, v and a.
  2. Torque: force times lever armTorque is force times lever arm; a force that acts at the axis, or points straight through it, makes no torque.
  3. Balance: seesaws, levers and beamsBalance needs zero net force and zero net torque; put the pivot where an unknown force acts so that force drops out.
  4. Moment of inertia and the parallel axis theoremI depends on the mass, how far it sits from the axis, and which axis you pick; add the parts about one common axis.
  5. Rotational dynamics: τnet = IαFind τnet, divide by I to get α, then use rotational kinematics; a pulley with mass needs its own τ = Iα equation.
  6. Rotational kinetic energy and work done by torqueRotational KE is ½Iω² and the work done by a torque is τΔθ; a rolling object splits its energy between moving and spinning.
  7. Rolling without slippingRolling means v = ωR and a contact point at rest; a smaller I/MR² ratio means a faster trip down a ramp.
  8. Angular momentum, angular impulse and conservationL = Iω or mvr⊥; with no net external torque, L is constant even when kinetic energy and linear momentum are not.

The big ideas

Every linear idea has a rotational partner

Displacement x pairs with θ, velocity v with ω, acceleration a with α, force F with torque τ, mass m with moment of inertia I, and momentum p with L. The laws pair up too: Fnet = ma becomes τnet = Iα, ½mv² becomes ½Iω², and FΔt = Δp becomes τΔt = ΔL. When a rotation problem looks unfamiliar, write the linear version first and then swap each symbol for its partner.

Torque depends on the lever arm, not just the force

A force only turns an object if its line of action misses the axis. The size of the turning effect is τ = r⊥F, where r⊥ is the perpendicular distance from the axis to that line. This is why a long wrench beats a short one, why you push a door far from its hinges, and why a light child far from a seesaw's pivot can balance a heavy child near it. Every balance question on the exam comes down to comparing lever arms.

Moment of inertia is about where the mass is

Two objects with the same mass can have very different moments of inertia. Because I = Σmr², each bit of mass counts by the square of its distance from the axis. Mass at the rim counts far more than mass at the center, so a hoop is harder to spin than a solid disk of equal mass and radius. Changing the axis changes I as well, which is what the parallel axis theorem handles. A shape change, like a skater pulling in her arms, changes I without changing mass.

Pick the tool that matches the question

Use τnet = Iα with kinematics when a question gives forces and times or angles. Use energy when it gives heights and asks for speeds, such as an object rolling down a ramp. Use conservation of angular momentum when the net external torque on a system is zero but its shape changes or two objects collide on an axle. Energy and angular momentum are not always conserved together. A skater pulling in her arms keeps L constant while her kinetic energy rises.

Study notes

8 topics. Each one opens with its key idea, then the detail you need to use it.

1. Angular kinematics: describing rotation

Key idea: Convert revolutions to radians first, then use the Unit 1 equations with θ, ω and α in place of x, v and a.

Rotation uses three quantities. Angular displacement θ is the angle an object turns through, measured in radians, where one full turn is 2π rad. Angular velocity ω is the rate the angle changes, in rad/s, and angular acceleration α is the rate ω changes, in rad/s². When α is constant, the Unit 1 equations carry straight over: ω = ω₀ + αt, θ = ω₀t + ½αt², and ω² = ω₀² + 2αθ. If α points against ω, it is an angular deceleration and the object slows down.

Every point on a rigid object shares the same ω, but points farther from the axis move faster, because they cover a bigger circle in the same time. The links are v = rω for speed and a = rα for tangential acceleration. On a wheel spinning at 20 rad/s, a point 0.30 m from the axis moves at 6.0 m/s, while a point 0.10 m out moves at only 2.0 m/s.

Worked example: a wheel spinning at 12 rad/s stops after 3 revolutions. Convert first, so 3 rev becomes 6π ≈ 18.8 rad, and then 0 = 12² + 2α(18.8) gives α ≈ −3.8 rad/s². The most common slip is plugging in 3 instead of 18.8, which makes the answer about six times too big. Graphs also work as in Unit 1, since the slope of an ω-versus-t graph is α and the area under it is the angular displacement.

2. Torque: force times lever arm

Key idea: Torque is force times lever arm; a force that acts at the axis, or points straight through it, makes no torque.

Torque is the turning effect of a force about a chosen axis. Its size is τ = rF sinθ, where r is the distance from the axis to the point where the force acts and θ is the angle between r and F. An easier way to read it is τ = r⊥F, where the lever arm r⊥ is the perpendicular distance from the axis to the line along which the force acts. Torque is measured in newton-meters (N·m).

This explains how you open a door. If you push at the hinge, r = 0, so the torque is zero however hard you push. If you push along the door straight toward the hinge, sinθ = 0, so again nothing turns. A force only twists an object when its line of action misses the axis.

Example: you pull a wrench with 25 N at 0.40 m from the bolt, at 30° to the handle, so the torque is 0.40 × 25 × sin30° = 5.0 N·m. A perpendicular pull would give 10 N·m, and doubling the handle length doubles the torque for the same force, which is why a longer wrench loosens a stuck bolt. Always multiply force by distance, because dividing them gives a number with the wrong units.

Torque also has a direction of rotation. Call counterclockwise positive and clockwise negative, then add the torques with their signs, because the net torque, not any single torque, decides how the rotation changes.

3. Balance: seesaws, levers and beams

Key idea: Balance needs zero net force and zero net torque; put the pivot where an unknown force acts so that force drops out.

An object in full equilibrium needs zero net force and zero net torque. Zero net torque means the object either does not rotate or keeps rotating at a constant ω, and seesaws, levers, shelves and beams all use both conditions.

The method is short. Draw every force at the point where it acts, placing the weight of a uniform object at its center. Then choose a pivot carefully, because any force acting at the pivot has zero torque and drops out of the torque equation. Finally, set the clockwise torques equal to the counterclockwise torques.

Seesaw example: a 30 kg child sits 1.5 m from the center, and a 45 kg child balances her at distance d on the other side. Since 30g × 1.5 = 45g × d, the distance is d = 1.0 m, so the heavier child must sit closer to the pivot.

Beam example: a uniform 4.0 m plank weighs 80 N and rests on a pivot 1.0 m from its left end. Its center is 2.0 m from the left end, which puts it 1.0 m to the right of the pivot, so its weight makes 80 N × 1.0 m = 80 N·m of clockwise torque. A downward push on the left end has a 1.0 m lever arm, so that push must also be 80 N. The force condition then gives the support: the pivot pushes up with 80 + 80 = 160 N.

4. Moment of inertia and the parallel axis theorem

Key idea: I depends on the mass, how far it sits from the axis, and which axis you pick; add the parts about one common axis.

Moment of inertia I is rotational inertia, which describes how strongly an object resists changes to its rotation. For one small mass, I = mr², where r is the distance from the axis, and for many masses you add them up as I = Σmr². Because r is squared, mass far from the axis counts much more than mass near it.

That is why shape matters as much as mass. A hoop of mass M and radius R has all its mass at the rim, so I = MR². A solid disk of the same mass and radius has I = ½MR², because much of its mass sits near the center, and a solid sphere has I = (2/5)MR². The AP Physics 1 equation sheet gives I = Σmr² and the parallel axis theorem, but not shape values like MR², ½MR² or (2/5)MR². A question states those when you need them, so your job is to compare and combine them.

I also depends on the axis. A thin rod of length L has I = (1/12)ML² about its center but (1/3)ML² about one end. The parallel axis theorem connects the two as I = I_cm + Md², where d is the distance from the center of mass to the new axis, so for the rod (1/12)ML² + M(L/2)² = (1/3)ML².

A composite object is simple once you know this, because you find each part's I about the same axis and then add. Take a 1.2 kg rod, 1.0 m long, with a 0.5 kg ball fixed to one end, spinning about its other end. Its I = (1/3)(1.2)(1.0)² + 0.5(1.0)² = 0.40 + 0.50 = 0.90 kg·m².

5. Rotational dynamics: τnet = Iα

Key idea: Find τnet, divide by I to get α, then use rotational kinematics; a pulley with mass needs its own τ = Iα equation.

Newton's second law for rotation says α = τnet / I. A larger net torque produces a larger angular acceleration, while a larger moment of inertia produces a smaller one. This is the rotational version of a = Fnet / m, and you use it the same way: find the net torque, divide by I, then apply angular kinematics.

Merry-go-round example: a child pushes tangentially with 60 N at the rim, 2.0 m from the center, on a merry-go-round with I = 400 kg·m² that starts from rest. The torque is 60 × 2.0 = 120 N·m, so α = 120 / 400 = 0.30 rad/s², and after 8.0 s the angular velocity is ω = 0.30 × 8.0 = 2.4 rad/s. Wrong answers on this type usually come from using the wrong time or the wrong I, so label each number with its units as you go.

Pulleys connect rotation and translation. Suppose a block hangs from a string wrapped around a pulley that has mass, so the string tension T gives the pulley a torque TR. The block's acceleration is a = αR, and it is less than g, because the tension pulls upward on the block. A pulley with mass needs its own τ = Iα equation, so check whether the question gives its I.

6. Rotational kinetic energy and work done by torque

Key idea: Rotational KE is ½Iω² and the work done by a torque is τΔθ; a rolling object splits its energy between moving and spinning.

A spinning object has kinetic energy even when its center stays still. Rotational kinetic energy is K = ½Iω², the twin of ½mv², so a flywheel with I = 2.0 kg·m² spinning at 10 rad/s stores ½ × 2.0 × 10² = 100 J.

A torque does work as it turns an object through an angle, W = τΔθ, with Δθ in radians. By the work-energy theorem, this work equals the change in rotational kinetic energy. If a 5.0 N·m torque turns that flywheel through 20 rad, its energy rises by 100 J to 200 J, while a friction torque would do negative work and drain energy from the rotation.

An object that moves and spins at once has both kinds of energy, K = ½Mv² + ½Iω². For an object released from rest at height h with no energy lost, conservation becomes Mgh = ½Mv² + ½Iω².

This is why shape decides a ramp race. Part of the energy from the drop has to go into spinning, and only the rest goes into forward motion. A hoop puts a bigger share of its energy into rotation than a solid sphere does, so the hoop moves more slowly at the bottom. A block sliding down a frictionless ramp does not spin at all, so all its energy goes into translation and it beats every rolling object to the bottom.

7. Rolling without slipping

Key idea: Rolling means v = ωR and a contact point at rest; a smaller I/MR² ratio means a faster trip down a ramp.

Rolling without slipping means the object rolls with no skidding where it touches the ground. That gives one key link, v = ωR, where v is the speed of the center, and every rolling motion question uses it to swap ω for v.

Think of each point's velocity as two parts added together: the center's forward speed v, plus a rotational speed ωR around the center. At the top, both parts point forward, so the top moves at 2v. At the bottom, the rotational part points backward with size ωR = v, so the two cancel and the contact point is at rest relative to the ground for that instant. This is why static friction, not kinetic friction, acts on a rolling object, and why that friction does no work, so mechanical energy is conserved.

Now combine v = ωR with the energy split. For a solid cylinder, I = ½MR², so its rotational KE is ½(½MR²)(v/R)² = ¼Mv². Its translational KE is ½Mv², which makes the total ¾Mv², so one third of the energy is rotational. Rolling down a ramp of height h, Mgh = ¾Mv² and v = √(4gh/3). Mass and radius cancel, so any two solid cylinders reach the bottom at the same speed. The smaller the ratio I/MR², the faster the roll: the solid sphere (2/5) beats the solid cylinder (1/2), which beats the hoop (1).

On a slippery surface the object skids instead, so v ≠ ωR and kinetic friction turns some energy into heat.

8. Angular momentum, angular impulse and conservation

Key idea: L = Iω or mvr⊥; with no net external torque, L is constant even when kinetic energy and linear momentum are not.

Angular momentum is the rotational twin of linear momentum, measured in kg·m²/s. For a rigid object L = Iω, and for a single particle L = mvr⊥, where r⊥ is the perpendicular distance from the reference point to the particle's line of motion. The particle does not need to move in a circle, so a 0.4 kg puck sliding at 5 m/s along a line passing 3 m from a point has L = 0.4 × 5 × 3 = 6 kg·m²/s about that point.

A net external torque changes L. The angular impulse τΔt equals ΔL, just as FΔt equals Δp, so a 4 N·m torque acting for 3 s changes L by 12 kg·m²/s.

If the net external torque on a system is zero, L stays constant and I₁ω₁ = I₂ω₂. A skater who pulls in her arms halves her I, so her ω doubles. A ball on a string pulled to half its radius doubles its speed, since mvr stays fixed. Kinetic energy is not conserved in either case. For the skater, K = L²/2I, so halving I doubles K. For the ball, halving r cuts I = mr² to a quarter, so with L fixed its K becomes four times larger. In both cases the extra energy comes from the work done pulling inward.

Collisions on an axle need care. When clay hits and sticks to a rod on an axle, the axle pushes on the rod, so linear momentum is not conserved. That push acts at the axis and makes no torque, however, so angular momentum about the axle is conserved.

Common mistakes

Drawn from the wrong answers students actually pick on these questions.

Answering a balance question with the weight alone, such as picking 60 N for a 60 N rod balanced off-center because it is the only force in the problem.

Balance depends on torques, not forces. Find the lever arm from the pivot to the rod's center, multiply it by the weight, and set that product equal to the unknown force times its own lever arm, which usually gives an answer different from the weight.

Dividing force by distance, using the force alone, or measuring the distance from the wrong point when calculating torque.

Torque is force multiplied by lever arm, τ = r⊥F, measured in N·m, and the lever arm runs from the axis to the force's line of action. For 40 N applied perpendicular to a handle at 0.3 m, the torque is 12 N·m, not 40/0.3 or 40 × 0.1.

Leaving the distance out of a particle's angular momentum, which gives L = mv, or multiplying by an extra factor of 2.

A particle's angular momentum is L = mvr⊥, used exactly once, so a 2 kg ball moving at 4 m/s on a 3 m circle has L = 24 kg·m²/s. The same formula applies to a particle moving in a straight line past a point, using its perpendicular distance from that point.

Calling a merry-go-round that slows because of friction, or a ball slowed by air resistance, an example of conserved angular momentum.

Friction and air drag exert external torques, so angular momentum is not conserved in those cases. The law is demonstrated when no external torque acts and the system changes shape, such as a ball on a string that speeds up as the string is pulled shorter. A planet in a circular orbit also has constant L, because gravity pulls toward the star and exerts no torque about it. The string example is the clearer demonstration, because a change in r forces a visible change in v while L stays fixed.

Tracking only part of the system, such as claiming that a turntable keeps the same ω, stops, or simply speeds up after a firecracker throws a mass off its edge.

Draw the system boundary around the turntable and the ejected mass together, because the total angular momentum of that system is what stays constant. The turntable's new ω depends on how much angular momentum the ejected mass carries away, so losing mass alone does not settle the answer.

Plugging the wrong number into a multi-step τ = Iα calculation, such as the wrong time or the wrong moment of inertia.

Write each step with its units: torque in N·m, then α = τ/I in rad/s², then ω = ω₀ + αt in rad/s. A merry-go-round pushed from rest with τ = 100 N·m and I = 500 kg·m² has α = 0.2 rad/s², so after 10 s it spins at 2.0 rad/s.

How this unit shows up on the exam

AP Physics 1 opens with 40 four-option multiple-choice questions in 80 minutes, followed by four free-response questions in 100 minutes. You have a calculator and an equation sheet, so the formulas for torque, rotational kinetic energy and I = Σmr² are provided, and the points go to students who apply them correctly.

Multiple-choice stems in this unit repeat a few shapes. Calculation stems give a force and a distance, or a torque and an I, and ask for torque, α, or ω after a set time. Balance stems describe a seesaw, lever or beam and ask where a child must sit or what force keeps it level. Comparison stems ask which object reaches the bottom of a ramp first, or which has the greater moment of inertia. Conservation stems ask what happens to ω when a skater pulls in her arms or a person walks toward the center of a turntable, or which situation actually demonstrates conservation of angular momentum. Symbolic stems ask for a composite object's I in terms of m, L and R, which tests the parallel axis theorem. Some practice questions also ask why a spinning top precesses: gravity's torque points sideways to L, so it swings the direction of L instead of changing its size. Precession is beyond the AP Physics 1 framework, which treats rotation about a fixed axis and does not test the vector direction of torque and L.

The free-response section rewards reasoning over arithmetic. Expect to sketch an ω-versus-t graph and read α from its slope, or to draw each force at the exact point where it acts. A lab design might hang masses from a string wrapped on a pulley and plot α against τ, so that the slope equals 1/I. Paragraph answers score when they name the law, the system and the reason the law applies, such as stating that no external torque acts on the skater, so L is constant and her ω rises as her I falls.

How the exam actually asks it

Real items from the AP Physics 1 bank, easier first. The answer is marked, and every wrong choice is explained — because knowing why a distractor is tempting is most of the work.

Worked example 1Easier
A wrench is used to tighten a bolt. The mechanic applies a force of 40 N perpendicular to the handle at 0.3 m from the bolt. What is the torque applied?
  1. A12 N*mCorrect
  2. B133 N*m
  3. C40 N*m
  4. D4 N*m

Why A is right

Torque = F * r * sin(theta) = 40 * 0.3 * sin(90) = 40 * 0.3 * 1 = 12 N*m. The force is perpendicular to the moment arm (theta = 90 degrees), so sin(90) = 1. The result follows from the rotational relationship given in the problem, usually through conservation of angular momentum or torque balance.
Why the other 3 choices miss
B
Incorrect because 133 N*m = 40/0.3 divides instead of multiplying force by distance.
C
Incorrect because 40 N*m uses only the force without the moment arm; torque requires multiplying by the distance from the pivot.
D
Incorrect because 4 N*m = 40*0.1 uses a moment arm of 0.1 m instead of 0.3 m.
Worked example 2Easier
Which quantity has the same units as angular momentum?
  1. Akg*m^2/sCorrect
  2. BN*m
  3. Ckg*m/s
  4. Dkg/m*s

Why A is right

Angular momentum L = I*omega has units of (kg*m^2)*(rad/s) = kg*m^2/s (since rad is dimensionless). This is the standard unit for angular momentum. The result follows from the rotational relationship given in the problem, usually through conservation of angular momentum or torque balance.
Why the other 3 choices miss
B
Incorrect because N*m is the unit for torque (force times distance); torque = dL/dt has units N*m = kg*m^2/s^2, not kg*m^2/s.
C
Incorrect because kg*m/s is the unit for linear momentum (p = mv), not angular momentum.
D
Incorrect because kg/(m*s) has no standard physical interpretation relevant to angular momentum.
Worked example 3Easier
A cylinder is rolling without slipping on a flat surface. Which of the following correctly describes the velocity of the point on the cylinder that is in contact with the ground?
  1. AIt moves downward at speed v
  2. BIt moves backward at speed v
  3. CIt moves forward at speed v (the center's speed)
  4. DIt has zero velocity relative to the groundCorrect

Why D is right

Any point on a rolling cylinder has a velocity equal to the center's translational velocity v plus its rotational velocity about the center. At the contact point, the rotational velocity is ωr, pointing backward, and rolling without slipping means ωr = v. The two cancel: v - ωr = v - v = 0. So the contact point is momentarily at rest relative to the ground, which is choice D.
Why the other 3 choices miss
A
The contact point's rotational velocity is tangent to the cylinder, which is horizontal at the bottom, and the translational velocity is also horizontal. Neither contribution points downward, so the point has no downward motion at that instant.
B
This counts only the rotational contribution, ωr = v pointing backward, and leaves out the forward translational velocity v of the center that cancels it.
C
This counts only the translational motion of the center and leaves out the backward rotational velocity ωr = v at the bottom. Speed v forward is the center's velocity, and the top of the cylinder moves at 2v.
Worked example 4Medium
A particle of mass 2 kg moves at 4 m/s in a circle of radius 3 m. What is its angular momentum about the center of the circle?
  1. A96 kg·m^2/s
  2. B24 kg·m^2/sCorrect
  3. C8 kg·m^2/s
  4. D48 kg·m^2/s

Why B is right

For a particle in circular motion, angular momentum L = m*v*r_perp, where r_perp is the perpendicular distance from the axis to the velocity vector (which equals the radius for circular motion). L = 2*4*3 = 24 kg·m^2/s.
Why the other 3 choices miss
A
Incorrect because 96 = 2*48, further overestimating.
C
Incorrect because 8 = m*v = 2*4, omitting the radius.
D
Incorrect because 48 = m*v*r*2 or m*(v*r)^2/r, some form of double-counting.

Can you do all of these?

Tick what you can do without looking. Anything left unticked is where to go back to.

0 of 9 ticked

Ready to test yourself?

Open practice pulls from the 22 free questions in this unit. The other 319 come with the one-time AP purchase, which unlocks every AP course.

Official topic list

The official course framework breaks this unit into 12 numbered topics.

  1. 5.1Rotational Kinematics
  2. 5.2Connecting Linear and Rotational Motion
  3. 5.3Torque
  4. 5.4Rotational Inertia
  5. 5.5Rotational Equilibrium and Newton's First Law in Rotational Form
  6. 5.6Newton's Second Law in Rotational Form
  7. 6.1Rotational Kinetic Energy
  8. 6.2Torque and Work
  9. 6.3Angular Momentum and Angular Impulse
  10. 6.4Conservation of Angular Momentum
  11. 6.5Rolling
  12. 6.6Motion of Orbiting Satellites

Key terms in Torque and Rotational Dynamics; Energy and Momentum of Rotating Systems

Ordered by how often our reviewed questions test them. Open any term to see the questions that use it.

The rest of AP Physics 1

Every unit with its share of the exam. You are on Unit 5.

  1. 1Kinematics12.5% of exam
  2. 2Force and Translational Dynamics20.5% of exam
  3. 3Work, Energy, and Power20.5% of exam
  4. 4Linear Momentum12.5% of exam
  5. 5Torque and Rotational Dynamics; Energy and Momentum of Rotating Systems19% of exam
  6. 6Oscillations6.5% of exam
  7. 7Fluids12.5% of exam